by: Darren Baker [ ]
Originally published on:
The following text is the introduction as supplied by ICM with this model.
One of the most numerous and famous cars in world history was the Model T produced by the Ford Motor Company. It became the first mass produced car. Affordable for the middle class, the first example of the model T was built on September 27th 1908. It had a four cylinder engine producing 22.5 hp. The mass production was launched at the Highland Park Ford Plant, Michigan from the beginning of 1914. There were 15,007,003 cars produced from 1908 to 1927. Model T cars were produced in various types, in particular some 1911 cars had open topped five seat touring bodies.
ICM has changed their packaging for all models, or so it would seem from the last samples that arrived with me. The product is now packaged in a plain cardboard flip top box. The usual box top lid made of thin card is then placed on the cardboard flip top box. I feel this is an excellent move on the part of ICM now that large numbers of models are being ordered online and have to survive handling by various postal services. Well done ICM. Inside this new packaging you will find
5 grey sprues
1 brass chromed sprue
1 clear sprue
4 vinyl rubber tyres
An instruction booklet
An inspection of the kit parts leaves a positive impression. There are no obvious moulding faults present such as flash or sink marks to be found. There are of course some ejector pin marks that will need to be tackled, but that is to be expected and ICM are improving all the time when it comes to placing them in hidden areas and they are getting smaller both in overall size and prominence. There are some flow lines present on the larger mouldings but these have not caused any noticeable deformities that I could detect. Another plus is that the gates between the sprues and moulded parts are of a reasonable size and not excessive in number. All told, off to a very good start.
The engine is fairly basic as they go, but that does not mean ICM have cut corners. Checking it against online images indicates that ICM has done a very good job of replicating the engine, right down to some very fine details being present, especially around the exhaust manifold. The addition of some wiring should bring this area right up to spec. While on the subject of the engine ICM has provided a brass chromed radiator front with a grey plastic rear. It is not chrome as in shiny silver; it is designed to replicate brass. The coating has been applied to tan plastic fortunately or by design, but it will be difficult to hide the area where it was connected to the gate on the sprue. The front half of the brass effect radiator has very nice raised detail of the Ford logo.
Chassis and Suspension
The chassis is an integral part of the vehicles floor pan and so there are no concerns about getting this area out of true. The suspension and drive are as you would suspect pretty simple in design, but again ICM has done a good job of replication here. My only complaint in this area is that I would have liked the ability to display the front wheels turned rather than having them fixed in dead ahead, this is just a personal thing as I feel it adds interest to the look of a finished model.
The wooden spoke wheels are very nicely replicated and love them or hate them white vinyl rubber tyres. The white vinyl is perhaps best left unpainted as I feel it would be hard to apply a more realistic colour than the vinyl already is.
The floor pan is very well replicated in this model having the textured detail present for both the step plate and the cab floor interior. Also present again is the Ford Logo embossed on the step plate. The separate part of the floor pan where the foot pedals locate also has the nicely embossed Ford logo present. The steering column and wheel is surprisingly well detailed with throttle and spark levers present as separate parts. The handbrake quadrant and bellow for the horn also well replicated. The seats or should I say two seat settees are really nice, painted in a red leather colour with some thoughtfully applied washes will make this area really stand out and catch the attention. The only downside here is that there are some ejector pin marks that will need attention on inner faces of the body panels.
The exterior body of the vehicle is reasonably detailed and should look the part. I will say I would have liked the option of having the doors opened or closed instead of being moulded as a one piece with the body, with that said I feel it would be possible to do a bit of scratch building and make it possible to have the doors displayed as you wish. The bonnet is supplied in two parts and so could be depicted open to display the engine, but I am sure that each half of bonnet has another hinged area which would need to be created by the modeller. The headlights and coach lights have been very well replicated with some very nice detail. The design of the lights could I believe be set up with working lights via the use of LED lighting. The soft top roof will need some ejector pin marks dealt with on its inner face, but otherwise should look the part.
The glazing parts supplied with the model are of a reasonable thickness and have good clarity.
This review is basically a repeat of my previous review; the only changes are the new longer roof, the side body panels and extra seats. Because the changes are minimal in number it really depends on which Model T you wish to replicate, Both this and the previous Model T release are very nice kits and will with careful painting look very eye catching in a cabinet or case. As you would expect there are a couple of issues with the ejector pin marks and I would have liked the doors to have the option of being shown open and the front wheels turned, but then again there is no such thing as a perfect model for everyone. If you are interested in the Ford Model T this kit is worth thinking about and I expect to see a few more Model T vehicles from ICM in the future.