login   |    register
Quick Wheel [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

Tool Review
135
Dragon Pz IV Wheel Masks
Dragon Pz IV/Brummbar/Hummel Wheel Masks for kit #6300, 6315, 6321, 6330, 6380, 6480
  • 001377

by: Bill Plunk [ WBILL76 ]

Introduction

A new manufacturer out of Poland, QuickWheel, has begun producing kit-specific wheel masks unlike any other mask product previously seen. Unlike the usual AM manufacturersí approach of using either PE or adhesive masks that are essentially one-time use products, the QuickWheel masks offer a different approach entirely. The focus of this review is mask QW-010 designed for use on the DML Pzkpfw IV/Brummbar kits 6300, 6315, 6321, 6330, 6360, and 6460 and would presumably also work on the Cyberhobby Brumbar Early kit 6497 since it has the same road wheel design as the DML kit 6460.

Review

The packaging of the item is very straightforward, consisting of the mask attached to a small square of cardboard via adhesive tape and enclosed in a zip-loc style bag with a product card stapled to the top. The mask itself consists of a square piece of black hard plastic measuring 8cm x 8cm with holes punched out for the road wheels and return rollers and a thin layer of blue vinyl laid over that to produce the mask. The mask has 16 holes for the road wheels and 8 for the return rollers, enough to hold one complete hull sideís worth of road wheel halves and return roller halves at a time.

The masks do not come with any instructions or directions but their use is straightforward enough that this will not really present an issue. The holes are deep enough to take each road wheel or return roller half individually and the fit is tight enough that friction alone will hold the wheel half in place while painting with the first use. Subsequent uses though tend to make the fit a little bit looser, so thatís something to keep in mind to avoid the possibility of having wheel halves going flying and potentially getting lost when the mask is reused.

For the purposes of this review I gave the masks a test drive using DML kit 6460 Brummbar Mid road wheels as that was the only designated kit I had on hand. Since it only has steel wheel return rollers, I could only test the road wheels. Prior to using the mask, I air brushed the rubber portions and then, once dry, inserted the wheels into the mask from the underside. The fit is tight on the first try so the machined tolerances on the holes are very close to that of the wheels. The wheels need to be seated well against the vinyl mask but if you push too far the vinyl will stretch a bit which I found makes it less precise on subsequent uses, so care is needed if you want to use the masks more than once.

The appropriate color was then air brushed for the hubs and one of the wheels slipped slightly in the mask even though I was using only 20 psi pressure, so some bleed over resulted on the first wheel which I attributed to a learning curve on my part more than anything else. I found that holding the wheel in place gently with a finger while painting helped on the second wheel to avoid this issue. Once the paint had dried, the wheels were gently popped out to complete the process and avoid stretching the vinyl into the hole in the process. Since the mask is designed to handle an entire hull sideís worth of wheels at a time, it took more time for me to prep the air brush and clean it than it did to actually paint the wheels. The vinyl surface of the mask cleaned up easily with just thinner and a q-tip and can conceivably be reused as long as the vinyl mask doesnít stretch too much over time.

Conclusion

The only serious drawback I found to this particular mask was the absence of sufficiently sized masks for the inner portions of the wheel hubs. The Pzkpfw IV (like many German vehicles) road wheels and return rollers have different diameters on the rubber portion on the inner surfaces vs. the outer surfaces. Since the mask circles are all the same size, you are left on your own for painting the interior hub portions as there isnít any provision otherwise. This means that the mask will provide an efficient solution only for the outer faces instead of for the entire wheels as I had hoped. In order to get a fully accurate masked look on the inner hubs, some other method such as a circle template or hand painting will still be required.

Overall I found the size of the mask to be conveniently sized for easy handling and being able to take a full hull-side at a time will definitely speed up the painting process. The mask is of good quality and durable materials and can be reused on multiple projects if youíre looking to build the additional kits itís designed for. At $12, it is reasonably priced and is recommended for those looking for a faster way to handle painting the outer faces of road wheels and return rollers.

QuickWheel's Pz III wheel mask is Reviewed Here on Armorama.
SUMMARY
Highs: Straightforward design and sturdy construction, capable of reuse, and a convenient solution to a long-standing problem for many modelers.
Lows: Absence of masks for the inner hub surfaces means this solution only partially addresses the problem of accurately masking and painting road wheels. Vinyl mask surface can stretch if not careful, causing bleed-over on subsequent uses.
Verdict: Recommended for those looking for an easy way to deal with masking and painting the outer surfaces of road wheels and return rollers.
Percentage Rating
85%
  Scale: 1:35
  Mfg. ID: QW-010
  Suggested Retail: $12 USD
  PUBLISHED: Apr 10, 2009
  NATIONALITY: Germany
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 88.80%
  MAKER/PUBLISHER: 88.69%

Our Thanks to Quick Wheel!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View Vendor Homepage  |  More Reviews  

About Bill Plunk (wbill76)
FROM: TEXAS, UNITED STATES

Like many, I started out in the hobby as a kid building airplanes to hang from my bedroom cieling. I took a long break from the hobby, returning in 2001 with an interest in armor inspired mostly by online gaming. WW2 armor, 1/35 scale, is my preferred genre with a special taste for the stranger vehi...

Copyright ©2019 text by Bill Plunk [ WBILL76 ]. All rights reserved.



Comments

Thanks for the review Bill, for some reason I thought these would be in 2 pieces with the wheels sandwiched between them, and then fronts and backs would be painted together. At the same time, I didn't think about the thin vinyl so as the 'full' rim gets painted...quite clever.
APR 09, 2009 - 01:53 PM
   

What's Your Opinion?


Photos
Click image to enlarge
  • 007165
  • 006131
  • 005229
  • 004252
  • 003253
  • 002281