login   |    register
Roden [ MORE REVIEWS ] [ WEBSITE ] [ NEW STORIES ]

In-Box Review
148
Trojan C
Roden North American Trojan C Trainer in 1:48
  • move

by: Richard West [ RAYPALMER ]


Originally published on:
AeroScale

History
The Trojan C was the United States Navy's carrier landing version of the North American trainer. The B, the Navy's primary version differed from the Air Force's A variant, having the much more powerful R-1820 engine as opposed to the R-1300, and a ventral air brake mounted mid-fuselage. The C variant further tailored the aircraft for Navy use by adding an abbreviated rudder to accommodate an arrestor hook and shorter propeller blades. Combined with the air brake and powerful engine of the Trojan B, these allowed the Trojan C operate from carrier decks.
Overview
Inside the corrugated box there are six plastic sprues and one for clear parts, as well as a full-size set of monochromatic instructions and a respectable decal sheet. Parts to build the Trojan B and D are included on the sprues, so there will be a spare rudder, propeller, set of wingtips, drop tanks and mg barrels.
The plastic itself is roughly gull grey, the panel lines are crisp but on the wider and deeper side. There is some very delicate flash but certainly nothing to complain about. Setting aside the tiny flash the moulding is very good. The finer parts, probes, pitots and undercarriage linkages are all sufficiently delicate looking. Detail on the landing struts is the strongest looking element. The engine is good but not great, the cylinders are quite dumbed-down and lack the overall crispness one would like to see.
Cockpit and Landing Gear
Including the tub itself there appears to be 26 parts for the cockpit. Detail on the IP's is good, but the side console is a bit less crisp. Which is unfortunate given that this area is much more visible when finished. Rudder pedals, throttle and control stick are all rendered well. The seats are respectable enough and thankfully without moulded-on belts.
The undercarriage appears to have 29 parts, including doors. Here there is very little to complain about. As out-of-the-box lading gear goes this is a very strong showing. Scissors, oleos, brakes, struts and rams are all well depicted. Only the addition of some brake lines will yield a truly good result.
Airframe and Powerplant
Canopy, flaps, rudder, ailerons, air brake, and arrestor hook are all positionable. As well as four (two on either side) vents on the cowling. Only the elevators require cutting away to be posed. All of the poseable control surfaces are moulded in two pieces. But the horizontal stabilizers are moulded whole. When one considers this it seems a bit like halving the other surfaces was simply padding the parts count. A small sin, but it's nice to have to do that much less gluing now and then.
The engine is nine pieces, seven of which will be visible. Seperate pushrods, exhausts and fuel delivery are all moulded to make the engine more interesting. Like the cooling vanes on the cylinders they are all a bit meaty, but at least the effort was made.
The Decals
Markings for two aircraft are provided. One attached to CV-16 USS Lexington ~1971 that sports a yellow cat's mouth and eyes at the cowl, red and white livery and a sundowner style rudder. The second aircraft is from VA-122 in Lemoore California ~1977. This aircraft is far more subdued sporting gull grey on white akin to contemporaneous non-training navy aircraft. The sheet has a pleasing number of stencils, likely all that were present on these aircraft but that is difficult to know for certain. They have no printer's mark save for the word Roden.
Conclusion
Overall this kit is very good. It has only one real shortcoming in the meaty moulding of the cylinder bank of the engine. Fortunately the kit redeems itself with superb poseability, excellent landing gear and a more than presentable cockpit.

SUMMARY
Highs: Great Undercarriage, Many Positionable Parts, Pleasing Level of Surface Detail
Lows: Less than ideal engine.
Verdict: Frankly I'm looking forward to building this. It's got a weak engine but that's more than simple enough to remedy. The Cyclone 9 is hardly a difficult thing to find aftermarket. Recommended.
Percentage Rating
90%
  Scale: 1:48
  Mfg. ID: 451
  Related Link: 
  PUBLISHED: Jul 28, 2013
  NATIONALITY: United States
NETWORK-WIDE AVERAGE RATINGS
  THIS REVIEWER: 78.67%
  MAKER/PUBLISHER: 86.97%

Our Thanks to Roden!
This item was provided by them for the purpose of having it reviewed on this KitMaker Network site. If you would like your kit, book, or product reviewed, please contact us.

View This Item  |  View Vendor Homepage  |  More Reviews  

About Richard West (raypalmer)
FROM: ONTARIO, CANADA

Copyright 2019 text by Richard West [ RAYPALMER ]. All rights reserved.



Comments

That disk between the cylinders is supposed to be there A better way to spend your time improving the engine is to replace the very over-scale ignition harness and push rods. Watch out for the decals; the white is not opaque enough to cover the orange without an underlay.
JUL 27, 2013 - 04:45 PM
Son of a! Did they all have that? Cyclone 9's I mean.
JUL 27, 2013 - 05:07 PM
I can't say for certain, but Google image search says that it's there more often than not. I expect that it's got something to do with the cowling design and forcing the cooling air to wrap around the cylinders properly
JUL 27, 2013 - 06:20 PM
This kit certainly has sparked my interest. Just might be my 1st ever trainer. Joel
AUG 08, 2013 - 03:56 AM
   

What's Your Opinion?


Photos
Click image to enlarge
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move
  • move