_GOTOBOTTOM
Armor/AFV
For discussions on tanks, artillery, jeeps, etc.
REVIEW
Leopard L7 Barrel
CMOT
Staff MemberEditor-in-Chief
ARMORAMA
Visit this Community
England - South West, United Kingdom
Joined: May 14, 2006
KitMaker: 10,954 posts
Armorama: 8,571 posts
Posted: Friday, September 04, 2015 - 07:18 PM UTC
Jason Bobrowich takes a look at the Leopard 1 L7 Gun Barrel “Naked” from Leopard Workshop in 1/35th scale and designed for use with Italeri, Revell, Takom, and Meng Leopard kits.


Link to Item

If you have comments or questions please post them here.

Thanks!
mshackleton
Visit this Community
England - South East, United Kingdom
Joined: December 16, 2007
KitMaker: 559 posts
Armorama: 517 posts
Posted: Saturday, September 05, 2015 - 06:55 PM UTC
Thank you Jason for your honest review:-)
Vodnik
Visit this Community
Warszawa, Poland
Joined: March 26, 2003
KitMaker: 4,342 posts
Armorama: 3,938 posts
Posted: Sunday, September 06, 2015 - 06:31 PM UTC
Nice, but to be honest I don't like the resin "counterweight". I understand that it was made separately to allow for inserting the fume extractor part from the muzzle end, but the way it was done makes the diameter of this counterweight too big. This is a minor flaw, but noticeable for me. In reality the difference in diameter between the barrel and this counterweight is minimal - sometimes even hard to notice in photos. But resin casting limitations meant that the part couldn't be made as thin as it should be to be fully accurate. Much better solution would be to machine a muzzle tip of the barrel to reduce its diameter slightly on the length of the counterweight. This way the fume extractor could still be easily put on the barrel and the counterweight could be of more correct diameter, as the thinner barrel tip would allow for thicker wall of resin part, without making the external diameter too big.

If I decide to buy this barrel, I will replace the resin counterweight with a single layer of Tamiya masking tape around the muzzle end - it should be enough and more in scale thickness. If cut precisely the ends of the tape should meet without any noticeable gap - and it could be placed on the bottom side anyway.
mshackleton
Visit this Community
England - South East, United Kingdom
Joined: December 16, 2007
KitMaker: 559 posts
Armorama: 517 posts
Posted: Monday, September 07, 2015 - 01:12 PM UTC
Thank you for your comments Vodnik. We decided to do the counterweight this way as this is one of three versions of this gun. The remaining two have sleeves which need to slide along the barrel. This is impossible with a turned counterweight and also makes the alternatives of two different collimators equally impossible.
CMOT
Staff MemberEditor-in-Chief
ARMORAMA
Visit this Community
England - South West, United Kingdom
Joined: May 14, 2006
KitMaker: 10,954 posts
Armorama: 8,571 posts
Posted: Monday, September 07, 2015 - 02:34 PM UTC
Mike I have only one concern about resin collars over a metal barrel and that is that resin does tend to shrink. Is there a risk of the resin spliiting in time?
Vodnik
Visit this Community
Warszawa, Poland
Joined: March 26, 2003
KitMaker: 4,342 posts
Armorama: 3,938 posts
Posted: Monday, September 07, 2015 - 04:02 PM UTC
Mike, my suggestion of machining the muzzle end of the barrel to reduce the diameter at the length of the counterweight would still allow you to slide the sleeves along the barrel, and at the same time you could make more accurate counterweights with or without the colimators.
 _GOTOTOP